SPECIFICATIONS SHEET FOR FLU-TECH IMS SERIES INJECTION MOULDING M/c.:- IMS200 TO IMS 1250

MODEL UNIT IMS 200 RAM TYPE IMS 315 RAM TYPE IMS 450 RAM TYPE IMS 515 RAM TYPE IMS 650 SWING PLATE IMS 850 SWING PLATE IMS-1250 SWING PLATE SCREW TYPE     A           B       C  A        B A               B A                  B             A           A A B A INJECTION UNIT:               Screw diameter mm 50        55        60 70          80 80             90 80                 90 110 120 140 160 Injection pressure Bar 2450   2026     1702 1740     1332 2080         1650 2211             1747 1623 1848 2508 1920 Swept volume cu. cm 491     594       707 1366     1784 2011         2545 2362             2990 4467 5428 9852 12868 Screw stroke mm 250 355                  400 470 420 480 640 Max. Injected weight(PS) Gms 447     541       643 1243    1623 1830         2316 2149              2721 4065 4939 8965 11710 Max. Injected weight(PE) Gms 349     422       502 970      1267 1428         1807 1677              2123 3172 3854 6995 9136 Injection rate* Cc/sec 157     190       226 308      402 452           573 553                636 2851 3392 4618 6032 Plasticizing rate* g/sec 18       22.5      26 39        56 72             90 65                  80 92 115 140 163 Screw length L/D 22       20         18 20        18.7 22             20 20                  18 20 20 23 20 Max. Screw revolutions 1/min            200             140 145 90 68 41 32 27 Heating capacity KW            15 18 32 30 51 61 110 No. of heating zones - 4 6 5 6 6 8 9 Nozzle holding force kN. 70 105 175 225 250 350 480 Nozzle stroke mm 350 400 460 500 750 750 1200 B. CLAMPING UNIT: Clamping force kN 2000 3150 4500 5150 6500 8500 12500 Opening force kN 138 200 300 337 181 181 352 Mould opening stroke mm 800 1000 1100 1100 1000 1050 1150 Min. mould height mm 250 300 375 550 500…900 525…950 575..1050 Max. daylight mm 1050 1300 1475 1650 1900 2000 2200 Distance bet. Tie bar mm (hxv) 550x550 710x710 820x820 850x850 940x940 1020x1020 1250 x 1250 Size of mould plates mm (hxv) 850x850 905X905 1200x1200 1225x1225 1400x1400 1600x1600 1900 x 1900 Ejector force( hyd) kN 60 110 130 150 250 270 375 Ejector stroke mm 150 150 200 350 300 250 350 N  Nozzle protrusion mm 30 30 30 30 65 65 75 C. ELECTRICAL: Pump Drive Motor Kw 30 37 45 55 90 110 2x90 Heating Kw 15 18 32 34 51 61 110 Total Connected Load Kw 45 55 87 99 141 171 290 D. GENERAL DATA: Machine dimensions M (lxwxh) 6x1.6x2 7.5x2.0x2.4 8.6x1.81x2.4 9.6x2.4x2.7 12x2.1x2.9 13x2.2x3.1 15.6x2.4x3.4 Oil tank capacity LIT 500 800 1200 1200 1100 2000 2200 Net weight(without oil) (approx) kg 8000 15000 24000 29000 42000 66000 98000

Referring to polystyrene depending upon material and processing conditions, SPECIFICATIONS SUBJECT TO CHANGE DUE TO CONTINUOUS R&D. Note: 10 kN =1 ton app. Shot Capacity in PS=0.91*Shot Volume, in PE=0.71*Shot Volume MODELS HIGHER THEN THIS CAN BE OFFERED ON REQUEST Extra long stroke and daylights available against request